Solar-driven Interfacial Evaporation Research Articles

Flexible Janus Black Silicon Photothermal Conversion Membranes for Highly Efficient Solar-Driven Interfacial Water Purification.

Photothermal conversion materials are critical in the development of solar-driven interfacial evaporation techniques; however, achieving a high energy conversion efficiency remains challenging owing to the high cost and instability of light-absorbing materials, in addition to the difficulties of simultaneously improving light absorption while suppressing heat loss. A black silicon (Si) powder with a porous structure was prepared by chemical etching of a low-cost commercial micron-sized Al-Si alloy, and a flexible Janus black Si photothermal conversion membrane was constructed. The partially broken spherical particles and porous structure obtained after etching enhanced the refraction of light from the Si powder, imparting the prepared membrane with an average light absorption rate of 95.95% over the solar spectrum. Evaporation from the membrane increased the intermediate water content and reduced the equivalent evaporation enthalpy. The thermal conduction loss was inhibited through a one-dimensional water transport structure, and the membrane achieved a water evaporation rate of 2.17 kg m-2 h-1 and a photothermal efficiency of 94.95% under 1 sun illumination. Benefiting from the broadband absorption and high photothermal efficiency of black Si powder, surface modification of hydrophobic polydimethylsiloxane, and directional salt-out structure design, the evaporation rate of the Janus black Si membrane-based system in a 10% NaCl solution was maintained >2.10 kg m-2 h-1 after 7 days of continuous evaporation cycles. The removal rate of metal ions from simulated seawater and from practical wastewater containing complex heavy metals reached >99.9%, indicating the promising potential of black Si membrane for application in solar-driven interfacial water purification.

Sandwiched solar interfacial evaporation system: Integrating phase change material/hydrogel/NiCo2O4 nanoflower for superior desalination

Solar-driven interfacial evaporation is a kind of sustainable and eco-friendly method of water treatment to alleviate the global water crisis. Here we demonstrate a novel sandwiched solar interfacial evaporator integrating phase change material (PCM), sodium alginate hydrogel (SA), and NiCo2O4 nanoflower featuring superb evaporation and glorious thermal energy management to achieve efficient energy utilization and long-term evaporation stability. After being combined with filter paper, NiCo2O4 nanoflower composites are adopted as the light absorber on the top layer, which can achieve an absorption of about 96.5 % in the full spectral range. SA hydrogel has been used as an intermediate layer for rapid water supply to the evaporation interface and to prevent salt deposition. Under one sun irradiation (1 kW m−2), the evaporator exhibits a high evaporation rate (1.94 kg m-2h−1) and excellent endurance in the treatment of high salt-concentration water. In particular, benefiting from the rational combination of PCM, the water production reached up to 12.13 kg m−2, which is 2.23 kg m-2higher than that of the evaporator without PCM under natural solar irradiation for 9 h. This work presents a promising concept for maximally utilizing intermittent solar irradiation energy and prolonged salt-free deposition desalination.

Recent Advances in High-Rate Solar-Driven Interfacial Evaporation.

Recent advances in solar-driven interfacial evaporation (SDIE) have led to high evaporation rates that open promising avenues for practical utilization in freshwater production and industrial application for pollutant and nutrient concentration, and resource recovery. Breakthroughs in overcoming the theoretical limitation of 2D interfacial evaporation have allowed for developing systems with high evaporation rates. This study presents a comprehensive review of various evaporator designs that have achieved pure evaporation rates beyond 4kgm-2h-1, including structural and material designs allowing for rapid evaporation, passive 3D designs, and systems coupled with alternative energy sources of wind and joule heating. The operational mechanisms for each design are outlined together with discussion on the current benefits and areas for improvement. The overarching challenges encountered by SDIE concerning the feasibility of direct integration into contemporary practical settings are assessed, and issues relating to sustaining elevated evaporation rates under diverse environmental conditions are addressed.

A robust and low-cost blended-fiber-based evaporator with high efficiency for solar desalination

The solar-driven interfacial evaporation (SDIE) is a clean and efficient technology to mitigate freshwater shortages. A robust and low-cost evaporator is essential for the practical implementation of SDIE systems. Herein, we design a fantastic blended-fiber-based evaporator using weaving techniques. This mixture fabric is crafted using polyethylene terephthalate fibers and linen threads. It makes full use of the excellent light absorption, tensile strength, and corrosion resistance of polyethylene terephthalate fibers. Meanwhile, the mixture fabric reserves exceptional air permeability and water supply capability of linen thread. We optimize the density of the mixture fabric by adjusting the reed count and the weft count. It is found that the combination of the 40 reed and a single weft yarn produces the most effective and stable evaporator. The optimized mixture fabric makes a good trade-off between the water supply to the evaporator and solar-thermal evaporation. As a result, the evaporator achieves a high evaporation rate and efficiency (∼1.53kg/m2/h, ~90 %) under 1 sun illumination, which surpasses most of the existing two-dimensional evaporators based on metal nanomaterials, polymers, carbon-based materials, and fabrics. Our work opens a new horizon for the development of efficient, scalable, flexible, low-cost, corrosion-resistant, and stable evaporators.

Novel cellulose-based films with highly efficient photothermal performance for sustainable solar evaporation and solar-thermal power generation

Solar-driven interfacial evaporation has received substantial attention in a variety of applications, including water purification, seawater desalination, and energy production. However, creating a straightforward, adaptable, and scalable method for correctly integrating hybrid solar-thermal systems continues to be a challenging task. Herein, we propose an economical, scalable, and environmentally friendly approach for achieving synergistic coupling of interfacial solar energy conversion for evaporation and low-grade thermal energy conversion to electricity by incorporating zinc oxide (ZnO) nanoparticle-modified MXene (ZNM- MXene) into cellulose nanofiber (CNF) films. The vacuum filtering approach produces CNF@ZNM-MXene composite films with enhanced photothermal conversion efficiency, capillary hydrophilicity, and thermal localization. Because of its rapid water transport capability, excellent sunlight absorption, and efficient solar-thermal conversion under 1 kW m−2 irradiance, the CNF@ZNM-MXene solar evaporator's evaporation rate reaches 1.27 kg m−2 h−1, and the solar-vapor conversion efficiency is as high as 82.15%, outperforming most previously reported solar evaporators. Moreover, when compared to a standalone thermoelectric (TE) module, the output power of the solar thermal conversion system coupled with a CNF@ZNM-MXene composite films and a TE module is boosted by 15.32 times. This work offers a practical and effective method for simultaneously capturing solar energy and desalinating saltwater.

Multifunctional Super-Hydrophilic MXene/Biomass Composite Aerogel Evaporator for Efficient Solar-Driven Desalination and Wastewater Treatment.

Solar-driven interfacial evaporation is recognized as a sustainable and effective strategy for desalination to mitigate the freshwater scarcity issue. Nevertheless, the challenges of oil contamination, salt accumulation, and poor long-term stability of the solar desalination process limit its applications. Herein, a 3D biomass-based multifunctional solar aerogel evaporator is developed for water production with fabricated chitosan/lignin (CSL) aerogel as the skeleton, encapsulated with carbonized lignin (CL) particles and Ti3C2TiX (MXene) nanosheets as light-absorbing materials. Benefitting from its super-hydrophilic wettability, interconnected macropore structure, and high broadband light absorption (ca. 95.50%), the prepared CSL-C@MXene-20mg evaporator exhibited a high and stable water evaporation flux of 2.351kg m-2 h-1 with an energy conversion efficiency of 88.22% under 1 Sun (1kW m-2) illumination. The CSL-C@MXene-20mg evaporator performed excellent salt tolerance and long-term solar vapor generation in a 3.5wt.% NaCl solution. Also, its super-hydrophilicity and oleophobicity resulted in superior salt resistance and anti-fouling performance in high salinity brine (20wt.% NaCl) and oily wastewater. This work offers new insight into the manufacture of porous and eco-friendly biomass-based photothermal aerogels for advanced solar-powered seawater desalination and wastewater purification.

Robust and multifunctional MXene/rGO composite aerogels toward highly efficient solar-driven interfacial evaporation and wastewater treatment

Given the ever-growing global water resource crisis, exploiting multifunctional materials featuring with high interfacial solar steam generation efficiency and good purification capability to achieving seawater desalination and wastewater treatment simultaneously are highly desired, yet it still remains a huge challenge to date. Herein, robust and multifunctional MXene/rGO (MRGA) and polydopamine & chitosan @ MRGA (CS&PDA@MRGA, CPM) three-dimensional composite aerogels with distinct interconnected cellular architecture were developed via a facile ice template-assisted chemical reduction self-assembly technology and subsequent sequential deposition modification. Due to the favorable graphene oxide-assisted assembly behavior, the resultant aerogels displayed a desirable mechanical robustness along with an excellent lightweight property. Benefiting from the strong electrostatic interaction deriving from aerogel surface moieties and dye molecules, MRGA-12 exhibited a prominent adsorption capability towards various dyes and achieved a superb adsorption capacity of up to 396.05 mg/g for malachite green (MG). Moreover, by virtue of the synergistic effect between the intentionally regulated low reduction degree of rGO and the integration of PDA and CS, CPM-12 achieved a dramatically reduced evaporation enthalpy of water from 2256 to 1617.18 J/g. Accordingly, this distinct feature resulted in an extraordinary solar-driven interfacial evaporation performance with a remarkable evaporation rate of 1.86 kg/m2/h and a high evaporation efficiency of 83.28 % under 1 sun illumination. Therefore, together with the terrific oil/water separation capability, these novel MXene-based aerogels hold a great potential for high-performance solar-driven interfacial evaporation and wastewater treatment.

Spongy and anti-pollution MXene/Ag2S/cellulose acetate membrane for sustainable solar-driven interfacial evaporation and water purification

Solar-driven interfacial evaporation (SIE) technology stands out as a promising approach for seawater desalination, leveraging solar energy efficiently in an environmentally friendly manner. However, the enrichment of organic pollutants on the interfacial evaporator has posed significant obstacles to the sustained implementation of SIE. Herein, a spongy, anti-pollution cellulose acetate membrane consisting of Ag2S-doping MXene nanosheets (MT-Ag2S/CAM) is proposed for sustainable desalination. The MT-Ag2S/CAM exhibited ultralow water vaporization enthalpy of 1.50 kJ g−1. Meanwhile, the MT-Ag2S/CAM, featured by high porosity (75.25 %), excellent light absorption and salt resistance, demonstrated a notable solar-driven evaporation rate of 1.8 kg m−2h−1 and a remarkable photothermal conversation efficiency of 91.6 % under one sun irradiation. Meanwhile, MT-Ag2S/CAM can realize a removal efficiency of 93.3 % for methylene blue, exhibiting outstanding anti-pollution and self-cleaning capabilities as well as long-term stability due to its strong mechanical properties. Finally, a device for sustainable desalination, water purification and clean water collection is designed and implemented in a practical SIE process.

Heat-Localized and Salt-Resistant 3D Hierarchical Porous Ceramic Platform for Efficient Solar-Driven Interfacial Evaporation.

Solar-driven interfacial evaporation (SDIE) is a highly promising approach to achieve sustainable desalination and tackle the global freshwater crisis. Despite advancements in this field, achieving balanced thermal localization and salt resistance remains a challenge. Herein, the study presents a 3D hierarchical porous ceramic platform for SDIE applications. The utilized alumina foam ceramics (AFCs) exhibit remarkable corrosion resistance and chemical stability, ensuring a prolonged operational lifespan in seawater or brines. The millimeter-scale air-filled pores in AFCs prevent thermal losses through conduction with bulk water, resulting in heat-localized interfaces. The hydrophilic nature of macroporous AFC skeletons facilitates rapid water replenishment on the evaporating surface for effective salt-resistant desalination. Benefiting from its self-radiation adsorption and side-assisted evaporation capabilities, the AFC-based evaporators exhibit high indoor evaporation rates of 2.99 and 3.54kg m-2 h-1 under one-sided and three-sided illumination under 1.0 sun, respectively. The AFC-based evaporator maintains a high evaporation rate of ≈2.77kg m-2 h-1 throughout the 21-day long-term test. Furthermore, it achieves a daily water productivity of ≈10.44kg m-2 in outdoor operations. This work demonstrates the potential of 3D hierarchical porous ceramics in addressing the trade-off between heat localization and salt resistance, and contributes to the development of durable solar steam generators.

Marine biomass-derived PDMS-based composite sponge for sustainably sourced solar-driven interfacial evaporation

Solar-driven interface evaporation has emerged as an attractive technology for addressing the pressing issue of water scarcity. Herein, from the perspective of utilizing and managing ocean resources, we have developed a comprehensive evaporator based on ocean biomass for efficient solar-driven interfacial evaporation, aiming to sustainably harness marine resources. The construction of a biomass-based evaporator was achieved using three-dimensional melanin nanoparticles (MNPs)@carboxymethyl chitosan (CMCS)/polydimethylsiloxane (PDMS) porous sponge, which exhibits highly hydrophilic and porous properties. In this study, MNPs functioned as the photothermal material and the CMCS-hydrophilic modified PDMS sponge was utilized as the supportive material. Owing to its outstanding photothermal conversion capability and ingeniously designed columnar shape with cold evaporation surface, the MCP sponge-based evaporator achieves a water evaporation rate of 2.04 kg·m−2·h−1 and an evaporation efficiency of 85% under 1sun illumination. In addition, the MCP sponge-based evaporator exhibits an outstanding desalination performance (93% salt rejection) and purification efficiency for dyes with natural sunlight. This groundbreaking study presents an innovative method by utilizing marine biomass-derived CMCS and MNPs as raw materials to construct a high-performance solar-driven interface evaporator, thereby tackling clean water generation and promoting the sustainability of marine ecosystems.

Flexible nanofiber composite solar evaporator for simultaneous interfacial evaporation and heavy metal ion adsorption

Solar driven interfacial evaporation (SDIE) is promising in harvesting fresh water because of its low cost, environmental friendless and sustainability; however, it is desirable but still difficult to achieve high efficiency heavy metal ion removal during SDIE. Here, we develop a superhydrophilic and stretchable nanofiber composite solar evaporator via carbon nanofiber (CNF) assembly on polymer fiber surface and then polydopamine (PDA) modification. The evaporation rate reaches as high as 1.456 kg m−2 h−1 with the evaporation efficiency of 91.40 %. The functional groups of PDA endow the nanofiber composite with good heavy metal ion adsorption performance that is proved to be an endothermic process, and SDIE can induce the increase of interface temperature and localized ion concentration and hence promote the Cr (VI) adsorption. One the other hand, NaCl ions are able to diffuse into body water without salt precipitation by virtue of powerful water transportation capability of the evaporation device. The dual Cr (VI) adsorption and NaCl ion diffusion channels ensure simultaneous and high efficiency Cr (VI) removal and seawater interface evaporation. SDIE accelerated heavy metal ion adsorption and the dual ion channel model provide inspiration to design multifunctional solar evaporator materials for waste water purification.

Black Silver-Decorated liquid metal nanofillers coupled with Glycerol-Modified hydrogel composites for high efficiency solar steam generation and thermoelectric conversion

Solar-driven interfacial evaporation (SDIE) holds great potential in alleviating global freshwater scarcity, which requires the design of efficient energy conversion devices. Herein, a quadruply engineered hydrogel-based evaporator is developed based on multipath regulation of the four key processes involved in SDIE, i.e., heat generation, energy utilization, water transportation, and evaporation. Surface-tailored liquid metal nanoparticles (EGaIn@Ag NPs) with a high photothermal conversion efficiency (PCE) of 30.4 % serve as the nanofiller to produce heat efficiently. Vertically aligned microchannels are constructed in the poly(vinyl alcohol) (PVA) hydrogel through directional freezing to accelerate water transportation. Glycerol is introduced to the PVA matrix to synergistically a) prevent heat loss from the interface to bulk water, and b) modulate the bonding state of water in the hydrogel to reduce the vaporization enthalpy. Such an elaborate design achieves a rather high evaporation rate of 3.26 kg m−2h−1 under 1 sun illumination. The hydrogel evaporator (EGaIn@Ag/PVAG) is applicable in treating real seawater and dye-contaminated sewages, showing favorable desalination durability and self-cleaning property. The synergistic design also imparts the hydrogel with thermoelectric power generation capabilities. This work offers a new insight into the synergistic design of SDIE devices, which is expected to inspire innovations in solar energy conversion and utilization.

Novel mushroom-like cotton-based evaporator for simultaneous freshwater production and salt harvesting via edge-preferential crystallization

Solar-driven interfacial evaporation (SDIE) has emerged as a promising technology to alleviate the global freshwater scarcity. However, the simultaneous collection of water and salt as resources while maintaining stable evaporation rate without salt contamination at the evaporation interface remains a huge challenge. Herein, we report a novel mushroom-like cotton-based evaporator, inspired by the vertical stem and inclined caps of mushrooms, for simultaneous freshwater production and salt harvesting. By depositing polyaniline (PANI) and carbon nanotubes (CNTs) onto the cotton fabric (CF), an evaporation rate of 1.88 kg m−2h−1 and a high solar evaporation efficiency of 99.4 % can be achieved in 3.5 wt% NaCl solution under one solar irradiation. Furthermore, a significant water collection efficiency of 70.2 % and a high salt harvesting rate of 42.1 g m−2h−1 can be derived. Even exposed to high-concentration (15 wt%) brine, our design still effectively prevents salt contamination. The distinctive edge-preferential crystallization not only avoids the salt contamination but also promotes the salt harvesting, due to the capillary force, the criss-cross water channels from the nature of cotton cloth, as well as the gravity-assisted water transport of the “mushroom cap” during evaporation. In addition, the low thermal conductivity (0.163 W m−1 K−1) of the photothermal layer with the integration of PANI and CNTs, as well as the vertical water upward transport via the “mushroom stem” effectively reduce the heat loss. This research holds great potential for seawater desalination applications with the comprehensive utilization of seawater resources.

A novel hierarchical chromium black membrane prepared by electroplating for desalination

Solar-driven interfacial evaporation (SDIE), a technology for local solar energy conversion through photothermal materials, has been greatly developed. The metal oxide semiconductors have excellent photothermal conversion performance and are considered the most promising materials for photothermal conversion. Hierarchical structure with large surface area is beneficial to improve the photothermal conversion efficiency through the light-trapping effect and reduces the evaporation enthalpy of water. Herein, chromium black (Cr, Cr2O3, CrO3-x) photothermal membranes (CBPM) with ganoderma-like hierarchical structure were prepared by electrochemical oxidation. Due to the small interlayer spacing of the ganoderma-like structure, the light absorption of CBPM (M7) can reach 78.53 %, which in turn promotes the conversion of solar energy due to the low thermal conductivity of the chromium black layer, resulting in a high evaporation rate of 1.64 kg m−2 h−1. The solar-to-vapor conversion efficiency is up to 90.39 % under 1 sun irradiation. Meanwhile, the superhydrophilicity of the membrane is conducive to salt redissolution at night, so there was not much performance degradation after 24 cycles. This study provides a new solution for water treatment using chromium black as a photothermal material with great potential for solar production of fresh water.

Efficient solar-driven interfacial evaporation using conjugated microporous polymer networks synthesized from Buchwald–Hartwig coupling

Solar-driven interfacial evaporation (SDIE) has been considered as an effective and sustainable technology to purify water. To optimize heat localization and regulate water-existing forms via developing excellent photothermal materials is a key strategy to enhance SDIE performance. Herein, three novel conjugated microporous polymer networks (namely PBPs) were readily synthesized via Buchwald-Hartwig coupling between aryl bromides and p-phenylenediamine. Under 1 sun irradiation, the pure PBP-He without any additives delivered an excellent water evaporation of 1.18 and 0.96 kg · m−2 · h−1 using pure water, nature seawater as water source, respectively, and the corresponding energy conversion efficiency was up to 81.1 % and 65.7 %. An ever-enhanced SDIE performance was found in the PBPs networks with increased amine-linked sites density. The study provided a promising CMPs-based photothermal conversion platform for water purification, photothermal therapy, and photothermal sterilization, etc.

Group VIII (Fe, Co, and Ni) based water evaporators for solar driven interfacial water evaporation: Performance optimization, applications and recent advances

Solar-driven interfacial evaporation (SDIE) is a promising technology for sustainable and efficient production of clean water, addressing the pressing issue of freshwater scarcity facing humanity. Given the high level of concern regarding this matter, it is crucial to continuously summarize the research achievements of predecessors to further advance SDIE technology. This review first discusses the key role of solar absorbers containing Group VIII elements, including Fe, Co, and Ni, in SDIE. Second, it explores strategies to improve SDIE performance, such as increasing light absorption, regulating water transport channels, implementing effective thermal management, and reducing the enthalpy of water evaporation. These strategies can effectively optimize the performance of the evaporator and improve energy utilization efficiency. Further, this review details the specific applications of SDIE technology in areas such as seawater desalination, wastewater treatment, and energy reuse. We aim to provide insights for developing stable and efficient SDIE systems, promoting their practical applications, and developing other potential applications.

Scalable Superhydrophilic Solar Evaporators for Long-Term Stable Desalination, Fresh Water Collection and Salt Collection by Vertical Salt Deposition.

Solar-driven interfacial evaporation (SIE) is very promising to solve the issue of fresh water shortage, however, poor salt resistance severely hinders long-term stable SIE and fresh water collection. Here, we report design of superhydrophilic solar evaporators for long-term stable desalination, fresh water collection and salt collection by vertical salt deposition. The evaporators are prepared by sequentially deposition of silicone nanofilaments, polypyrrole and Au nanoparticles on a polyester fabric composed of microfibers. The evaporators feature excellent photothermal effect and ultrafast water transport, due to their unique micro-/nanostructure and superhydrophilicity. As a result, during SIE the salt gradually deposits vertically rather than occupies larger area on the evaporators. Consequently, long-term stable SIE with high evaporation rates of 2.4-2.1 kg m-2 h-1 for 3.5-20 wt % brine in continuous 10 h is achieved under 1 sun illumination. Meanwhile, the loosely deposited salt can be easily collected, realizing zero brine discharge. Moreover, scalable preparation of the evaporator is achieved, which exhibits efficient collection of high quality fresh water (10.08 kg m-2 in 8 h) via SIE desalination under weak natural sunlight (0.46~0.66 sun). This strategy sheds a new light on the design of high-performance solar evaporators and their real-world fresh water collection.

Experimental analysis of a solar interfacial evaporation under high power concentrator

Solar-driven interfacial evaporation in solar distillers is recently intensively investigated. This work presents a new distiller system based on bottom-heating/interfacial evaporation process driven by high power concentrated solar energy. This system applies Annual Fresnel solar concentration and a circular Fresnel lens, increasing input solar energy. The 1 D water supply wick is elected as the interfacial evaporator to satisfy water evaporation demand by capillary suction. Solar distillers with high-power concentrator are experimentally tested and the results are discussed in this work. This work aims at analyzing the bottom-heating/interfacial evaporation performance under concentrated sunlight. The concentration ratio of an Annual Fresnel solar concentration and a circular Fresnel lens is 62.4. Further optimization of the distiller is carried out according to the concentrators and low ambient temperature requirements of interfacial evaporation. Performances of different distillers are compared. The results show that, the cumulative freshwater productivity of the interfacial evaporation and bottom-heating distiller are 21.25 kg/(m2·day) and 15.98 kg/(m2·day), respectively. The maximum gain output ratio of the interfacial evaporation is 72.1%, higher than the bottom-heating distiller. The maximum temperature of interfacial evaporation surface is 81.53 C∘.

Synergism of solar-driven interfacial evaporation and photo-Fenton Cr(VI) reduction by sustainable Bi-MOF-based evaporator from waste polyester

The integration of interfacial solar steam generation and photocatalytic degradation technology has provided a promising platform to simultaneously produce freshwater and degrade pollutants. However, constructing low-cost, multi-functional evaporators for treating Cr(VI)-polluted water remains challenging, and the synergistic mechanism on Cr(VI) reduction is fuzzy. Herein, we propose the combined strategy of ball milling and solution mixing for the sustainable production of Bi-MOF microrod from waste poly(ethylene terephthalate), and construct Bi-MOF-based solar evaporators for simultaneous photo-Fenton Cr(VI) reduction and freshwater production. Firstly, the evaporator comprised of Bi-MOF microrod and graphene nanosheet possesses high light absorption, efficient photothermal conversion, and good hydrophilic property. Attributing to the advantages, the hybrid evaporator exhibits the evaporation rate of 2.16 kg m−2 h−1 and evaporation efficiency of 87.5% under 1 kW m−2 of irradiation. When integrating with photo-Fenton reaction, the Cr(VI) reduction efficiency is 91.3%, along with the reaction kinetics of 0.0548 min−1, surpassing many advanced catalysts. In the outdoor freshwater production and Cr(VI) reduction, the daily accumulative water yield is 5.17 kg m−2 h−1, and the Cr(VI) reduction efficiency is 99.9%. Furthermore, we prove that the localization effect derived from the interfacial solar-driven evaporation enhances H2O2 activation for the photo-Fenton reduction of Cr(VI). Based on the result of density functional theory, Bi-MOF microrod provides rich active centers for H2O2 activation to produce active sites such as e− or ·O2−. This study not only proposes a new strategy to construct multi-functional solar evaporators for freshwater production and catalytic reduction of pollutants, but also advances the chemical upcycling of waste polyesters.

Numerical Simulation Technologies in Solar-Driven Interfacial Evaporation Processes.

Solar interfacial evaporation technology has the advantages of environmentally conscious and sustainable benefits. Recent research on light absorption, water transportation, and thermal management has improved the evaporation performance of solar interfacial evaporators. However, many studies on photothermal materials and structures only aim to improve performance, neglecting explanations for heat and mass transfer coupling or providing evidence for performance enhancement. Numerical simulation can simulate the diffusion paths and heat and water transfer processes to understand the thermal and mass transfer mechanism, thereby better achieving the design of efficient solar interfacial evaporators. Therefore, this review summarizes the latest exciting findings and tremendous advances in numerical simulation for solar interfacial evaporation. First, it presents a macroscopic summary of the application of simulation in temperature distribution, salt concentration distribution, and vapor flux distribution during evaporation. Second, the utilization of simulation in the microscopic is summed up, specifically focusing on the movement of water molecules and the mechanisms of light responses during evaporation. Finally, all simulation methods have the goal of validating the physical processes in solar interfacial evaporation. It is hoped that the use of numerical simulation can provide theoretical guidance and technical support for the application of solar-driven interfacial evaporation technology.